Instructions for operators of DJI Mavic 3, 3 Pro 3 Classic quadcopters and separate (!) instructions for DJI Mavic 3T, Mavic 3E and Matrice 30(T) with firmware “1001,”
The Compass Module is designed for low-field magnetic sensing with a digital interface and perfect to give precise heading information.
This compact sensor fits into small projects such as UAVs and robot navigation systems.
The sensor converts any magnetic field to a differential voltage output on 3 axes
Instructions for drone operators with “1001,” firmware version
a Mavic3, Mavic3 Classic, Mavic3Pro om pyccкux xaxepob The drone has “1001,” firmware version. This allows you to use the drone bypassing some restrictions imposed by the manufacturer.
Firmware changes:
– DRONE D and OpenDroneld disabled; – NFZ disabled;
– added the “Anti-spoofing, fast take-off without BRS” mode,
– FCC activated on the drone itself (additionally 5.8 GHz frequency and high transmission power are used
data – the communication range with the drone increases), all restrictions are removed (range, altitude, etc.) if you are not logged into the DJI FLY application account
the range limit is set to “no restrictions” and the default maximum altitude is 10 km 5
independent of location on the map (even in areas with height restrictions),
– Airsense system is turned off
– added the ability to descend when the lower sonar is obscured,
blocked Possibility of flashing to the Zavoi version,
Additionally from version 34: – added the ability to automatically take off the drone at 2000, 1000, 500, 300, 200 or 100 meters Up at
loss of connection with the remote control. This allows you to get away from the electronic warfare (anti-drone gun), which is why communication is lost,
– The “landing in hand” mode is turned on; the dran does not bounce off the hand when landing, because “smart” is turned off
landing”; – added the ability to control the mode of disabling autolanding when the battery is completely discharged, the drone will not automatically try to land on the last percent of the battery;
Additionally, from version 36: the function of recording and storing flights has been removed; flight trajectories cannot be extracted from the drone (except for Zrgo),
the OpenDronelD functionality has been disabled, the function that sends data about the drone via WiFi, the commands “fec_on”, “fcc_off” have been added to enable the forced activation of FCC shutdown
(disabling is necessary for drones that have amplifiers installed to operate only at 2.4 GHz),
– so that when you are in NF2, warnings do not appear on the remote control; the service information sent from the drone to the remote control has been corrected;
NF2
Some of these changes can be “turned on” or “turned off” by entering a command in the “Name” field 6
“Information” window of application settings 0 FLY
Safety
Management
Camera
Transfer
Information
Information
Name
Name –
DJHVAVICS-DEAA35 7
Modal
0.3
Information
Application version
1.9.9
gps_off,
Drain firmware
01.00.1100 Check for spills
The drone can fly “without GPS” and “with GPS”:
In firmware “1001,” the ability to fly with complete ignoring of data from (“Anti-spoofing, fast takeoff without GPS”), with forced coordinates (0; 0), has been added. In this mode in
GPS module
The number of satellites graph displays a white ZERO.
Strong
Signal PRE Satellites
– Telegram channel for transmitting feedback and downloading instructions
Russian Hackers to the Front,
Switching between modes “without GPS” and GPS using the <<CINE”/“NORMAL” switch or the “gps_on,” command /
“You can use ‘gps_off’.
produce or central
Switching between modes In the firmware, the switch position corresponds to the modes:
You can switch right in flight!
we are GPS
CGPS
ANURMALS = sgps_on The drone will fly naturally
SLINE agus off, Flight without 675 data
(coordinates will be 0.0 throughout the flight). Flight only by camera visually based on satellite data.
